• fits most bikes 
• ultra-tough cube-tec protection 
• weatherproof 3m self-adhesive backing 

• Backed with ultra-strong 3M self-adhesive 
• Two kits universally designed to fit most MTBs and EMTBs 
• Ultra-tough Cube-Tec material to withstand the gnarliest of impacts

• Scratches and stone chips on your pride and joy? Hell no! Get protected with the Muc-Off Bike Protection Series. 
• We offer two separate kits designed for MTB and EMTBs, and available in four epic graphic options to suit every style, the Frame Protection Kit is made up of multiple universally designed shapes and sizes to cover all the high-risk areas on your bike. 
• Developed from the ground up and featuring the new proprietary Muc-Off Cube-Tec material, the Frame Protection Kit forms a barrier around your bike that’s strong enough to withstand the gnarliest of impacts, whilst being flexible enough to fit pretty much any frame geometry. 
• Each of the 45 pieces contained within the kit are backed with ultra-strong 3M self-adhesive backing, which means they’re super easy to install and will stay firmly in place whatever the conditions – So you can focus on keeping it pinned! 

• Downtube width dimensions: 85-100mm width
• Extra wide downtube pieces to cover wider E-Bikes
• Easy to apply: Simply peel off and install!
• Ultra-Tough Cube-Tec protection shields against scratches, scuffs, stone chips and other damage to your frame
• Durable, weatherproof 3M adhesive
• 45-piece pack will fit most E-MTB’s with wider down tubes
• Available in loads of awesome designs!

1. Clean your bike thoroughly before application. For best results and optimum durability spray Muc-Off Disc Brake Cleaner or Dry Degreaser onto a clean, dry microfibre cloth and wipe over the surface to ensure it is contaminant free. (Always test the disc brake/dry degreaser cleaner on a small inconspicuous area prior to use to ensure finish compatibility!) 
2. Try to fit the guards in a clean and warm environment, this will help achieve good adhesion to the surface. Top Tip! If you are applying in colder conditions and have access to a hairdryer, then carefully warm the surface. This will help achieve an optimal adhesive bond. 
3. Peel the guards off the backing material and line up the centre of the guards to the area you are applying. NB: It’s important you start with each sticker in the dead centre of the area you are applying so chill and take your time on this section! Then slowly rub down the middle, working your way out to the sides pushing out any air bubbles to the edges. Top Tip! You can easily trim the shapes as required, if necessary, with clean, sharp scissors if you need to fit around any challenging shapes or frame mounts etc. 
4. Use a clean microfibre cloth to firmly rub down the guards onto the surface and make sure you cover all areas with even pressure. 
5. Sit back and admire your freshly wrapped pride and joy, now go ride.

1. Start by gently heating the surface of the stickers with a hairdryer. This will help soften the adhesive, then slowly start peeling up a corner of the guards and peel back as carefully as you can, try to keep the adhesive attached to the protective layer so it all comes off in one piece. 
2. Once each protection guard is removed use Muc-Off Glue & Sealant Remover to easily remove any residue before re-installing your new guards! (Always test the Glue & Sealant Remover on a small inconspicuous area prior to use to ensure finish compatibility!). *age restrictions may apply!

What if the sticker doesn’t fit the area or component I am fitting it to perfectly?

The stickers can be easily trimmed down to size with scissors and we’ve even designed the stickers with set trimming indent slots to help facilitate with this in areas we think may need to be adapted for the perfect fit.

What if I apply the protection stickers incorrectly or not straight?

Don’t worry, stay calm, then very carefully and slowly peel the stickers back. If you have access to a hair dryer try and apply some heat to the area as this will help soften the adhesive and allow re-positioning of the sticker.  When applying the clear stickers, using water to help apply these will also allow easy repositioning when fitting.

Can I use a pressure washer to clean my bike after applying the frame protection stickers? 

It is safe to use a bike specific pressure washer like ours, however do not point the pressure washer nozzle close up and directly towards the edge of the protective sticker.

Can I clean my bike with Bike Cleaner after applying the frame protection?

Yes but we recommend leaving them for at least 24 hours before getting any cleaner or water on them so the adhesive has time to achieve  an optimal adhesive bond to the surface.

Do I have to use water and a squeegee to apply the clear gloss and clear matt protection stickers?

Yes we recommend using water to apply these stickers to achieve the best clarity under the stickers. This method helps push out all air bubbles and imperfections so you are left with a crispy clear finish.

• 45-piece pack is designed to fit most front suspension forks 
• Choose between DH/Enduro/Trail or E-MTB kit depending on bike type